2013年路虎LandRover Freelander2/L359电路图 [JLR 21 20 43_3E - FREELANDER 2 iEWD (3a)]

    Interactive Electrical Wiring Diagrams (iEWD)

    © Jaguar Land Rover Limited 2014

    While every effort is made to ensure accuracy, design changes to the vehicle may be made in the period between the completion of this publication and the introduction of vehicles. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic, mechanical, recording or other means without prior written permission from Jaguar Land Rover Limited. Paper copies of this document are uncontrolled, always refer to the electronic source material for the latest information.

    BEFORE USING THIS PUBLICATION

    HEALTH AND SAFETY

    Always follow health and safety guidelines, specifically the Electrical Precautions detailed in the Workshop Manual.

    Important

    The information provided in this publication is for use only by competent, qualified auto-electricians. Good product knowledge is assumed, as well as the ability to access and use recommended test equipment and other reference material provided.

    Test equipment and other reference material

    The information in this publication should be used in conjunction with the recommended test equipment; refer to Workshop Manual. Other reference material includes: Electrical Revision Documents (ERD), Technical Service Bulletins (TSB) and the Workshop Manual.

    Battery disconnection and reconnection

    It is imperative that any information relating to battery disconnection and reconnection is followed; refer to the appropriate sections in the Workshop Manual.

    Fault diagnosis

    Always use the recommended test equipment and test procedures for correct and reliable fault diagnosis; refer to the appropriate sections in the Workshop Manual.

    NOTE: Before starting electrical checks on the vehicle, ensure that relevant mechanical functions operate satisfactorily; refer to the appropriate section of the Workshop Manual.

    INTERACTIVE WIRING DIAGRAMS (iEWD)

    Using The Wiring Diagrams

    Introduction

    The interactive wiring diagrams (iEWD) combines two separate publications, the Electrical Wiring Diagrams (EWD) and the Electrical Reference Library (ERL). The iEWD is part of the JLR diagnostic toolset, providing a new method for easily linking between the two sets of data and provides quicker:

    • Navigation around the diagrams

    • Identification of connector location and pinout

    • Connector and data search capability

      Note: The connector and data search feature is not fully developed and currently only functions for the page being viewed. In the future, a fully developed iEWD will render data that is fully searchable.

    Section numbering

    The sections in this publication are ordered to match the Global Outline numbering system as found in the current Workshop Manual. The Power and Ground distribution circuits can be found under section 414-01, BATTERY, MOUNTING AND CABLES.

    Note: Where circuit diagrams show more than one sub-system, the circuit will be located in the section that carries the first-named sub-system, for example: Starting and Charging will be located under section 303-06 Starting System, since 'Starting' is the first-named sub-system.

    Circuit sheet numbering

    The figures in brackets to the bottom right of the page indicate a circuit sheet number and the total number of sheets per circuit, for example (01 / 05) represents sheet 1 of 5.

    Navigating the diagrams

    The navigation control tool comprises four directional scan arrows and three buttons: zoom in, zoom out, zoom reset.

    An alternative method of navigating is:

    • Pan

      Left-click and drag

    • Zoom

      Double left-click (zoom in), Double right-click (zoom out)

    To follow a wire path to another sheet from the chosen arrow head:

    • Make a note of the letter positioned directly above the arrow head

    • Left-click on sheet number directly below the arrow head

    On the newly located sheet, find the corresponding arrowhead and letter.

    Components

    After each component description, a translation code is displayed in brackets, for example: Starter relay (R102), Engine control-module (ECM)(D131). The codes can be ignored.

    Note: A dotted outline indicates that the component identified is not shown in its entirety.

    Connectors

    Connectors and header joints are identified by their corresponding connector number with a numbered suffix to indicate the pin-out detail of the wire, i.e. C1E116B-15 identifies connector 1E116B, pin number 15. Wire insulation colors are listed in a table at the end of this section. Where wires have a predominant color with a secondary color tracer, the main color is identified first, i.e. WH-BK - white with a black tracer.

    Wire length

    The wire length (in millimetres) is displayed after the color and cross sectional area; for example, BU,2.5,470. In this example, the figure, 470 indicates the approximate position of the harness splice is 470mm from connector C1E116B.

    Line Types

    Crossed wires as illustrated above show an example of how a twisted pair of wires may be represented on the circuits.

    The arrows illustrated above show an example of the page break symbols, identifying that the circuit continues at the corresponding letter on the sheet number indicated.

    Ground points

    Ground points are identified with an eyelet symbol and a connector number, except where components are grounded through its fixings, when only the eyelet is shown.

    The cup and ball symbol represents the male and female halves of the connector. Most connectors plug directly into a component but some are wired directly to the component using a ‘flylead’ as with C1EC01BM above.

    Electrical Reference Library (ERL)

    Introduction

    The Electrical Reference Library (ERL) data is now accessible directly by following the hyperlinks from the interactive wiring diagrams.

    Identification of connector location and pinout

    To access connector details, hover the pointer over the connector number on the wiring diagram and left-click; the details will be displayed including, where available, a graphic of the connector face-view and a location image.

    The list of Connectors to the right of the location image presents the opportunity to view connector details for each annotated connector shown on that image.

    Note:Connectors that are shown in the image are not necessarily part of the same electrical system, but are physically located in the area illustrated.

    Refer to Connector details for an explanation of how to interpret the rest of the data.

    Connector details

    Connector details comprises:

    • Connector Designation – The designated reference, prefixed 'C' or 'G' in the case of some ground connections.

    • CONNECTOR HOUSING SERVICEABLE – The part identified is available through the normal parts ordering process.

    • CONNECTOR HOUSING NOT SERVICEABLE – The part identified is not available.

    • Description – Usually derived from the component to which the connection is made.

    • Location – Used in conjunction with the photograph to indicate the location of the connector.

      Note: References to the LH or RH side given in this document are made when viewing the vehicle from the rear.

    • Qualifier – For some connectors it is not possible to represent all possible conditions. An image may show a left-hand condition, the right-hand condition may be similar and is identified as such using a Qualifier, for example: LHD condition illustrated.

    • Location Image – Shows the location of the subject connector. For convenience, some images identify more than one connector.

      Note: Images do not necessarily represent the optimum method for accessing a connector, always refer to the appropriate Service Repair Operation within the Workshop Manual before attempting to access a connector.

    • Face View – An outline of the connector housing, viewed from the front, showing pin numbers (if applicable).

    • Part No. – The part number as it appears on the harness drawing (if applicable).

    • Color – If applicable, the color of the connector housing is shown. NATURAL is used to describe connectors with a clear/translucent plastic finish.

    • Cavities – Identifies the number of cavities within the connector.

    • Harness – Identifies the harness description (English only).

    • Wire Chart (Pin-out table) – A five column table, giving details of each wire within the connector:

    Sample Wire Chart and Service Repair Information

    The five columns provides specific wiring information related to each connector.

    1. Cav: The connector pin (cavity) number.

      NOTE: Wires may not be fitted to all cavities.

    2. CSA: The cross sectional area of the wire in mm².

    3. Col: The color of wire populating the connector pin.

    4. Cct: Identifies the model or option which uses the wire. 'ALL' means applicable to all models in the range fitted with the feature or system in question. In instances where different models, features or systems require different color wires to be fitted in a cavity, each instance of the cavity is included in the pin-out table.

    5. Destn: The destination of the wire.

    The last seven columns provide Service Repair Information where applicable.

    NOTE: When the seven columns are not shown, no SRI is available for that particular connector.

    If a connector uses more than one type of terminal (pin), different service repair information may be required.

    1. Pre-Terminated Lead: Pre-terminated leads (including bespoke harnesses where applicable).

    2. Extract Tool: Connector pin extractor tools.

    3. Crimpers: Terminal applicator tool.

    4. Wire Stripper: Wire cutter/stripper.

    5. Heat Shrink Sleeve: Adhesive-lined heat-shrink sleeving.

    6. Ident Sleeve: Wire color identification sleeves.

    7. Splice: Splice connectors.

    Wire chart and service repair information
    Cav CSA Col Cct Destn Pre-Terminated Lead Extract Tool Crimpers Wire StripperHeat Shrink SleeveIdent SleeveSplice

    1

    2.5

    GN-RD

    B2CAF

    C2BP01F

    418-549-11

    418-612

    418-116A

    418-117

    418-104

    418-112

    418-107

    2

    1.5

    GN

    B2CAF

    C2BP01F

    -

    -

    -

    -

    -

    -

    -
    Wire chart only
    Cav CSA Col Cct Destn

    1

    2.5

    GN-RD

    B2CAF

    C2BP01F

    2

    1.5

    GN

    B2CAF

    C2BP01F

    Abbreviations and acronyms

    Abbreviation Description

    ABS

    Anti-lock braking system

    AUTO

    Automatic transmission

    AVI

    Audio video input

    BBUS

    Battery backed-up sounder

    BJB

    Battery junction box

    BSM

    Blind spot monitoring

    CAN

    Controller area network

    CJB

    Central junction box

    CVD

    Continuously variable damping

    D4

    Diesel engine - Straight-four

    DAB

    Digital audio broadcasting

    DBJB

    Dual-battery junction box

    DPF

    Diesel particulate filter

    DSC

    Dynamic stability control

    DTC

    Diagnostic trouble code

    DV6

    Diesel engine - V6

    DV8

    Diesel engine - V8

    EJB

    Engine junction box

    EGR

    Exhaust gas recirculation

    FFBH

    Fuel fired booster heater

    GPS

    Global positioning system

    HID

    High intensity discharge

    HLD

    High level definition

    HS CAN

    High speed controller area network bus

    LF

    Low frequency

    LH

    Left hand

    LHD

    Left hand drive

    LIN

    Local interconnect network

    MMM

    Navigation system module

    MOST

    Media orientated system transport

    M/S

    Manual/sport

    MS CAN

    Medium speed controller area network bus

    NA

    Naturally aspirated

    NAS

    North American specification

    PDC

    Park distance control

    PV6

    Petrol engine - V6

    PV8

    Petrol engine - V8

    PV8NA

    Naturally aspirated engine - V8

    PV8SC

    Super charged engine - V8

    RF

    Radio frequency

    RH

    Right hand

    RHD

    Right hand drive

    SAI

    Secondary air injection

    SCL

    Steering column locking

    SDARS

    Satellite digital audio radio service

    SRS

    Supplemental restraint system

    TCM

    Transmission control module

    TMC

    Traffic message channel

    TPMS

    Tire pressure monitoring system

    TV

    Television

    UK

    United Kingdom

    USB

    Universal serial bus

    VICS

    Vehicle information and communication system

    Wire color codes

    The following list contains wire color codes used on the vehicle harnesses.

    Code Color

    BK or B

    Black

    GN or G

    Green

    PK or K

    Pink

    LG

    Light green

    BN or N

    Brown

    OG or O

    Orange

    VT or P

    Purple

    RD or R

    Red

    GY or S

    Grey (Slate)

    T

    Transparent

    BU or U

    Blue

    WH or W

    White

    YE or Y

    Yellow

    HARNESS REPAIRS

    Repair Methods

    CAUTION: Do not attempt to repair any part of a wiring harness unless appropriate training has been received. Refer to the Workshop Manual, Section 418-02, Wiring Harnesses, DESCRIPTION AND OPERATION.

    FIBRE OPTICS

    General

    The fibre optic system installed uses Media Oriented Systems Transport (MOST), which is a multimedia network, optimized for automotive applications. Its design allows it to provide a low-overhead and low-cost interface for the simplest of devices, such as microphones and speakers. More intelligent devices can automatically determine the features and functions provided by all other devices on the network and establish sophisticated control mechanisms without distracting the driver.

    Under normal installation conditions the system is robust and failures should not occur. However, since the optical fibres convey data using infra-red light, it is vital the passage of light down the fibre is unobstructed. Obstruction of infra-red light can be caused by:

    • Contamination of the fibre ends.

    • Damage to the fibre ends.

    • Bending, kinking or damaging the cable.

    NOTE: Fibres damaged by kinking or exposure of the optical core due to abrasion must be replaced.

    Handling

    Take special care to avoid damage or contamination when handling or working in the vicinity of fibre optic cables and connectors.

    NOTE: Damage or contamination includes scratches to the cable ends and pollution caused by dust, dirt, oil or moisture.

    CAUTION: When handling fibre optic cables cleanliness is of paramount importance. The fibre ends should not be touched even with clean bare hands as the natural oils deposited from the skin may penetrate the fibre or may cause dirt to adhere to the fibre end.

    System malfunctions and unnecessary warranty claims can be minimised by following these guidelines:

    • After disconnection of any cables, carefully install appropriate dust caps to protect the mating faces of the connectors from damage or contamination.

    • Avoid introducing tight bends (less than 30mm radius) or kinks into the fibre optic cable during service or repair. Tight bends or kinks could impair operation, cause immediate system failure, or future system failure.

    • Avoid excessive force, strain or stress on the fibres and connectors, especially permanent stress after reinstallation.